Bend Roof Pros provides professional chimney flashing in Bend, OR for residential and commercial properties across Central Oregon. Bend has two kinds of chimney and they fail for two different reasons. Knowing which one you own decides whether you need a roofer, a mason or a sheet metal shop. They also cost very different amounts to fix.
The older Westside and downtown houses from the mill era carry real masonry. There, the leak is almost always at the counterflashing, and the daily cycle is what breaks it. Brick, mortar and steel all change dimension at different rates through a twenty-six degree swing, and a surface-mounted piece of metal stuck on with a bead of mastic is being asked to absorb that difference every single day. It cannot.
We cut a reglet into the mortar joint, set two-piece counterflashing so the outer leg can slide freely over the base flashing, wedge and repoint it, and we never bed new metal into joints that are already crumbling. If the mortar will not hold a clean cut, tuckpointing has to come first, and we say that before you get a roofing price rather than after the invoice. Tuckpointing is masonry work, and we will refer it out.
Most newer Bend homes have a framed chase with a galvanized cap on top instead. That cap is the actual roof of the chimney, and the thin factory ones sag, pond and rust through from underneath long before the roof around them fails. Replacing one is sheet metal work: a fabricated stainless or heavy-gauge cap with a cross break so water runs off, a hemmed drip edge, and a properly sized collar around the flue.
Crickets are not optional on the uphill side of a wide chimney, whatever the width trigger in the code happens to say. Snow and needle debris pile behind a chase all winter here and stay there through freeze after freeze, and a cricket is the whole difference between water traveling around the obstruction and water sitting against it. We frame ours from dimensional lumber and sheathe them, never from tapered foam.
If a fireplace has not been used in years and the chimney is now purely a leak source, we will price capping and abandoning it. Sometimes the cheapest correct answer is to stop having a chimney at all. That conversation goes better before you have paid for a fourth repair to the same joint.
Our licensed and insured team brings the right materials and equipment to every job — concealed floating clips slotted for daily panel travel, sealant selected by its published movement class, hand-sealed tabs set in dabs of asphalt roof cement, fluoropolymer coil finishes over steel substrate, high-temperature self-adhered underlayment beneath relaid tile, laminated low-emissivity glazing in deck-mounted skylight units — and backs the work with a written workmanship warranty. We serve Bend and nearby communities including Redmond, Sisters, La Pine, Sunriver.
What We Handle
Everything our chimney flashing in Bend covers
One crew, one point of contact, and the full range of chimney flashing work in Bend, OR. If it is on this list we do it in house rather than handing it to a subcontractor:
- chimney flashing repair bend or
- chimney leak bend oregon
- counterflashing installation central oregon
- chimney cricket bend
- chimney chase cover replacement deschutes county
- chimney flashing replacement bend oregon
- roof chimney leak redmond oregon
- chase cover bend or
- step flashing repair bend oregon
- chimney reflash central oregon
- masonry chimney roof repair bend
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Bend services.
Materials, equipment and how we do chimney flashing
The difference between chimney flashing that lasts and chimney flashing that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with concealed floating clips slotted for daily panel travel, sealant selected by its published movement class, hand-sealed tabs set in dabs of asphalt roof cement, fluoropolymer coil finishes over steel substrate, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Bend job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. Years of roofing work in Central Oregon means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do chimney flashing outside Bend
Bend Roof Pros covers Bend and the surrounding communities of Central Oregon. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Chimney Flashing in Redmond, OR — Deschutes County, population 33,274
- Chimney Flashing in Sisters, OR — Deschutes County, population 3,064
- Chimney Flashing in La Pine, OR — Deschutes County, population 2,512
- Chimney Flashing in Sunriver, OR — Deschutes County, population 2,023
- Chimney Flashing in Terrebonne, OR — Deschutes County, population 1,393
- Chimney Flashing in Tumalo, OR — Deschutes County, population 558
Start on the Bend Roof Pros homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why Bend Chooses Bend Roof Pros
- ✓We specify for a 26.5 degree average daily temperature range rather than for one season, which changes the sealant, the clip and the fastener before it changes the shingle
- ✓Inspections are booked early in the morning, because every joint on a roof is at its widest before the sun reaches it and an afternoon look misses the gap
- ✓We will not apply a field coating between October and mid-May, and that refusal is printed on the proposal rather than explained away on the phone
- ✓Shingle tear-offs are scheduled inside the warm window, and any course laid outside it is hand-sealed and noted with the working temperature on your invoice
The standards behind chimney flashing
Quality here is not a matter of opinion — it is written down. The chimney flashing work we do in Bend follows published industry standards: NRCA publishes the Roofing Manual, the industry's reference for details and slope minimums, and Asphalt Roofing Manufacturers Association sets the shingle application and ventilation guidance the warranties reference. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every chimney flashing project in Bend gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free chimney flashing free estimate in Bend, or request a quote and we'll get right back to you.